The URL can be used to link to this page

17-055_FlorenceBank_LoanServicing_permit_RLOAN SERVICING DEPARTMENT FLORENCE, MASSACHUSETTS 01062 85 MAIN STREET FLORENCE BANK Renovations to: INDEX TO DRAWINGSGENERAL NOTES 1. THE GENERAL CONTRACTOR WILL BE RESPONSIBLE FOR ALL OTHER WORK THAT IS SHOWN IN THE CONTRACT DOCUMENTS THAT IS NOT SPECIFICALLY IDENTIFIED TO BE THAT OF A SUB-CONTRACTOR; INCLUDING ALL WORK THAT IS SHOWN IN THE CONTRACT DOCUMENTS, THAT IS NOT IDENTIFIED AS BEING ANY CONTRACTOR'S SPECIFIC RESPONSIBILITY. THE SCOPE OF THE WORK OF THE SUB-CONTRACTOR'S ARE IDENTIFIED IN THEIR INDIVIDUAL SPECIFICATION SECTIONS. 2. THE GENERAL CONTRACTOR WILL PROVIDE-BARRICADES, TEMPORARY LIGHTS, TEMPORARY TELEPHONE SERVICE, AND CLEAN-UP SERVICE TO THE WORK AREA. 3. THE GENERAL CONTRACTOR WILL VERIFY ALL DIMENSIONS AND CONDITIONS AT THE JOB SITE PRIOR TO PROCEEDING WITH THE WORK. THE GENERAL CONTRACTOR WILL COORDINATE WORK ACCORDINGLY WITH ALL SUBCONTRACTORS AND THE OWNER. 4. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR THE COMPLETE AND THOROUGH CLEAN-UP AT THE END OF THE JOB, AND FOR DAILY REMOVAL OF CONSTRUCTION DEBRIS AND CLEAN-UP. 5. THE GENERAL CONTRACTOR WILL PERFORM MINOR SPACKLING AND REPAIRS TO EXISTING WALLS THROUGHOUT THE WORK AREA AS IS REQUIRED IN PREPARATION FOR NEW FINISHES. 6. IT WILL BE THE GENERAL CONTRACTOR'S RESPONSIBILITY TO VERIFY AND EXECUTE ALL WORK IN ACCORDANCE WITH MASSACHUSETTS BUILDING CODE, 8TH EDITION, WITH ALL OF ITS REFERENCED PUBLICATIONS AND ALL OTHER APPLICABLE STATE, FEDERAL, AND LOCAL CODES AND REGULATIONS. 7. IT WILL BE THE GENERAL CONTRACTOR'S RESPONSIBILITY TO SEE THAT ALL WORK PERFORMED IS IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION'S LIFE SAFETY CODE (N.F.P.A.-101, CURRENT EDITION). 8. THE GENERAL CONTRACTOR WILL BE RESPONSIBLE FOR INITIATING, MAINTAINING, AND SUPERVISING ALL SAFETY PRECAUTIONS AND PROGRAMS NECESSARY FOR THE COMPLETION OF THE WORK, AND AS REQUIRED BY THE OWNER. 9. THE GENERAL CONTRACTOR WILL PROVIDE THE OWNER WITH INSURANCE CERTIFICATES FOR THE REQUIRED INSURANCE PRIOR TO STARTING THE WORK. 10. THE GENERAL CONTRACTOR WILL FILE FOR AND SECURE ALL APPROVALS, PERMITS, AND CERTIFICATES OF COMPLIANCE AS REQUIRED. 11. THE GENERAL CONTRACTOR SHALL FULLY COMPLY WITH OWNER'S "INTERIM LIFE SAFETY POLICY" DURING THE ENTIRE CONSTRUCTION PERIOD. CONSTRUCTION CLASSIFICATION OCCUPANCY CLASSIFICATION APPLICABLE CODES & STANDARDS BUILDING CODES AND STANDARDS 1. MASSACHUSETTS STATE BUILDING CODE (780 CMR), 8TH EDITION 2. MASSACHUSETTS ELECTRIC CODE 2009 3. NFPA 101 LIFE SAFETY CODE (2000 EDITION) 4. MASSACHUSETTS ARCHITECTURAL ACCESS BOARD REGULATORS (521 CMR) 5. MASSACHUSETTS STATE PLUMBING CODE (248 CMR) ALTERNATES B - BUSINESS TYPE 2A / 3B NOT APPLICABLE GI001 GI002 AD101 A101 A501 A102 TITLE SHEET INFORMATION SHEET DEMOLITION FLOOR PLAN FLOOR PLAN INTERIOR ELEVATIONS,WALL TYPES, DOOR AND ROOM FINISH SCHEDULE REFLECTED CEILING PLAN AF101 FURNITURE PLAN E101 ELECTRICAL LIGHTING AND POWER PLAN AD102 DEMOLITION REFLECTED CEILING PLAN TITLE GI001 BW/GS/RK SEAL: MARK DATE ISSUE --- PROJECT NO: PROJECT ARCHITECT: PROJECT MANAGER: DRAWN BY: DATE: COPYRIGHT: 17-055 REK REK 12/20/2017 SHEET TITLE: CONSULTANT: 64 GOTHIC STREET, SUITE 1 NORTHAMPTON, MA 01060 T 413.585.1512 F 413.586.7945 www.haiarchitecture.com H AI Architecture, Inc. Loan Servicing Department 1st Floor Florence Bank 85 Main Street Florence, MA 01062 Renovation for: PROJECT: REK A B B R E V I A T I O N S Z O N I N G A N A L Y S I S NOT APPLICABLE G R A P H I C S Y M B O L S INTERIOR ELEVATION DESIGNATION DETAIL IDENTIFICATION ELEVATION LETTER SECTION DESIGNATION ON SHEET WHERE SECTION IS TAKEN; SHEET NUMBER WHERE DRAWN SECTION DESIGNATION ROOM AND NAME NUMBER ON SHEET WHERE DETAIL IS TAKEN; SHEET NUMBER WHERE DRAWN ON SHEET WHERE SECTION IS TAKEN; SHEET NUMBER WHERE DRAWN DETAIL DESIGNATION DOOR NUMBER KEY NOTE WALL TYPE HEIGHT MARK DETAIL DESIGNATION ON SHEET WHERE DETAIL IS TAKEN; SHEET NUMBER WHERE DRAWN DETAIL DESIGNATION SECTION DESIGNATION AIR CONDITIONING INSULATION INTERIOR LAMINATE JOIST JOINT LAVATORY JANITOR INSIDE DIAMETER JST. JT. LAM LAV JAN. ID INSUL. INT. W/ W.C. WD. WATER CLOSET WITH WOOD FACE OF FINISH ELECTRIC WATER COOLER FACE OF MASONRY FACE OF STUD FLOOR DRAIN FOUNDATION FIRE EXTINGUISHER FIRE EXTINGUISHER CABINET FIRE HOSE CABINET FINISH FLOOR GYPSUM WALL BOARD HANDICAPPED GENERAL GAUGE GALVANIZED GRADE GENERAL CONTRACTOR GLASS GLAZE HEIGHT HOLLOW METAL HOT WATER HEATER HEATING, VENTILATING AND EXHAUST EXISTING EXPANSION EXTERIOR EAST EXPANSION JOINT ELEVATION ELECTRICAL ELEVATOR EQUAL EQUIPMENT EMERGENCY ROOM DRINKING FOUNTAIN DIAMETER DIMENSION DOWN DOOR DETAIL DRAWINGS CERAMIC TILE FACE OF FOUNDATION WALL F.D. HGT. HM HWH HVAC H.C. GA GEN. GALV G.C. GL. GRD G.W.B. GLZ F/F F.O.M. F.O.S. FDN. F.E. F.E.C. FHC FIN. FLR. F.O.F. EJ EWC EX. EXP. EXT. EXH EL. ELEC. ELEV. EQ. EQUIP. E.R. DIM DN DR DTL. DWGS. E DIA CT D.F. SUSPEND (ED) STRUCTURALSTRUCT. SUSP T.O.W. UR VB V.I.F. VERT. VCT VEST. UNO UOD UH T.O.S. T/SLB THK TLT TYP. T.O.F. T T.O. TEL SYS TOP OF WALL ELEVATION UNLESS NOTED OTHERWISE VINYL COMPOSITION TILE TOP OF STEEL ELEVATION URINAL VERIFY IN FIELD VINYL BASE VESTIBULE VERTICAL TOP OF SLAB UNDERSIDE OF DECK UNIT HEATER TOP OF FOUNDATION THICK TYPICAL TOILET TOP OF TELEPHONE TREAD SYSTEM STOR. STD STL. S.S. SPEC SIM. SECT. REQ'D R.O. RM. RGH R.D. REFR REF REINF SPECIFICATIONS STAINLESS STEEL STORAGE STANDARD STEEL SECTION SIMILAR REQUIRED ROUGH OPENING ROOM ROUGH REFRIGERATOR REINFORCE ROOF DRAIN REFERENCE ABOVE FINISH FLOOR CLEAR (DIMENSION) ANCHOR BOLT AIR CONDITIONER ARCHITECT CABINET CONTROL JOINT BUILDING LINE BOARD BUILDING BLOCK BLOCKING BOTTOM OF BEARING BRICK ADJACENT ALTERNATE ALUMINUM ANCHOR ANODIZED CONCRETE CONSTRUCTION CONTINUOUS CLOSET CENTER CEILING CONCRETE MASONRY UNIT COLUMN COMPACTED (COMPOSITION) CONTRACTOR ACOUSTICAL COL CONC. CONST. CONT. COMP CONTR CLR CTR CLG CMU CL CJ BRK CAB. BD BLDG BLK B.O. BRG BLKG A.F.F. BL ALT. ALUM. ANCH ANOD ARCH AB AC ACOUST ADJ. PLYWD PTN PT PTD. PVC PLAM. PLAS PBD PL N.T.S. OPP. OPG. O.F.C.I. O.C. ND NEC N.I.C. N NAT PARTITION POLYVINYL CHLORIDE PLYWOOD PAINTED PAINT PARTICLE BOARD PROPERTY LINE PLASTIC LAMINATE PLASTER NOT TO SCALE OPPOSITE ON CENTER OWNER FINISHED, OPENING NECESSARY NATURAL NOT IN CONTRACT NAPKIN DISPENSER NORTH MEP MISC MULL M.O. MIN MTL. MFR. MAS. MAX. MECH. PLUMBING MANUFACTURER MISCELLANEOUS MASONRY OPENING MINERAL CORE MULLION METAL MECHANICAL MASONRY MAXIMUM BOTTOMBTM. EXTERIOR INSULATION & E.I.F.S. FINISH SYSTEM FIELD VERIFYF.V. MTD.MOUNTED CONTRACTOR INSTALLED O.F.O.I.OWNER FINISHED, OWNER INSTALLED SF SQUARE FOOT STD STANDARD MECHANICAL, ELECTRICAL, INSULATED HOLLOW METALIHM SCW SOLID CORE WOOD INSULATED STEELIS TI TEMPERED INSULATED KICKPLATE (HEIGHT")K(12) 1/4 WG 1/4" WIRE GLASS 1/4 T 1/4" TEMPERED GLASS CORNER GUARDCG EXISTING TO REMAINETR S.M.SURFACE MOUNTED FIXTURE HEIGHTS 15"-48"MIN. MAX.17"-25"36" MAX.TO SPOUT OUTLET27" MIN.KNEE CLEARANCE48"MAX48"MAX.Per NFPA 72 the strobe shall be no less than 80" and no greater than 96" AFF. When clg heights don't allow for a min. height of 80", strobes shall be mounted within 6" of clg 17" MIN.33"-36"MIN. MAX.34" MAX.TO RIMINSULATE ALL PLUMBING W/ TRUEBRO LAVATORY GUARD OR EQUAL FINISH FLOOR 7"-9" MIN. MAX.15"-48"MIN. MAX.15"-48"MIN MAX12" MAX. FOLD DN. SEAT AS REQ'D 48"48" 42" MIN.12" MIN.33"-36"MIN. MAX.LINE FINISH FLOOR LINE 13-1/2" MIN. FINISH FLOOR LINE The highest operable part of telephone, including dial, handset and coin deposit slots shall be within the reach ranges specified in ABA Section 30815"MINAccessible storage spaces shall be within at least one of the reach ranges specified in ABA Sections 308 29"MIN.27"MIN.40" MAX. TO BTMEDGE OF REFLECTINGSURFACEMount on side wall closest to water closet, can not be mounted behind opposite bars Grab bars shall be between 1-1/4" and LQDQGORFDWHGD"FOU from wall 17"-19"MIN. MAX.16"-18" MIN. MAX. HIGHEST OPERABLE PART 15"-48" DEPENDENTON FORWARD OR SIDE REACH36"x48" CLR. FLR. SPACE FIRE HORN AND LIGHT FIRE EXTINGUISHER CABINET PUBLIC TELEPHONE (ELEVATION) 30"x48" CLR. FLOOR SPACE FOR FORWARD APPROACH PUBLIC TELEPHONE (PLAN) CLOTHES HOOK/ROD DUPLEX RECEPTACLE 30"x48" CLR. FLOOR SPACE LAVATORY (ELEV.)LAVATORY FORWARD APPROACH (PLAN) MIRROR DRINKING FOUNTAIN (PARALLEL APPROACH) FREE STANDING OR BUILT-IN UNITS DRINKING FOUNTAIN (FORWARD APPROACH) WALL & POST MOUNTED CANTILEVERED UNITS ACCESSIBLE DRINKING FOUNTAIN (ELEV.) TOILET PAPER DISPENSER/HOLDER TOILET CLOSEST SIDE WALL GRAB BARS (ELEV.) TOILET REAR WALL GRAB BARS (ELEV.) TOILET (SIDE ELEV.) Flush controls for water closets shall be on the open side of water closet. Operable parts shall be placed w/in one of the reach ranges specified in ABA section 308 TOILET (FRONT ELEV.) URINAL (ELEV.) URINAL (PLAN) MIN. SHOWER CONFIGURATION PLAN - PER VAMC SOAP DISPENSER SANITARY NAPKIN - TAMPON DISPENSER PAPER TOWEL DISPENSER20"MAX2'-0"MAX.80"-96" AFFFIRE ALARM PULL STATION42"-48"OPTIONAL POST OR BASE 4'-0"MAX.8" MIN.30"x48" CLR. FLOOR SPACE 30"x48" CLR. FLOOR SPACE6" MAX. TOE CLEARANCE 6" MAX. TOE CLEARANCE 36" MIN. 24" MIN.15"-48" DEPENDENTON FORWARD OR SIDE REACH15"-48" DEPENDENTON FORWARD OR SIDE REACHOPENSIDE NOTE: CONTROLS OF OPERATING MECHANISMS MUST BE PLACED WITHIN AT LEAST ONE OF THE REACH RANGES SPECIFIED IN UFAS SECTION 4.2.5 & 4.2.6 HIGHEST OPERABLE PART FOR FORWARDOR SIDE REACHFOR FORWARDAPPROACHFOR FORWARDAPPROACHSEE PLAN FORUNOBSTRUCTEDSIDE ORFORWARD REACH54" MIN. TRANSFER SIDE SIDE WALL 17" MAX.TO RIM44" TYP.FLUSH CONTROLSW/IN REACH RANGEABA SECTION 3089" MIN.TOECLEARANCE17"MIN.5" MAX. 5" MAX. SPOUT LOCATION SPOUT LOCATION 15" MIN. 15" MIN.9" MIN.TOE CLEARANCE8" MIN. KNEE CLEARANCE CLEARANCE AT TOILET (PLAN) 60" MIN.56"MIN.MIRROR 16"-18" MIN. MAX. 30"x48" CLR. FLOOR SPACE 56"x60" MIN. CLR. FLOOR SPACE -REQUIRED CLEAR FLOOR SPACES, CLEARANCE AT FIXTURES AND TURNING SPACES SHALL BE PERMITTED TO OVERLAP. -DOOR SHALL NOT SWING INTO THE CLEAR FLOOR SPACE OR CLEARANCE REQUIRED FOR ANY FIXTURE. DOORS SHALL BE PERMITTED TO SWING INTO THE REQUIRED TURNING SPACE. 1 A101 A B C D 2 A102 1 A101 CONFERENCE ROOM 1005 201 2 CEILING HEIGHT EL. = 100'-0" 36 A101 EXIT REQUIREMENTS: OCCUPANCY LOAD: 2,388 SF @ 100 SF / OCCUPANT = 24 OCCUPANTS MINIMUM EGRESS WIDTH CALCULATIONS (DOORS, RAMPS & CORRIDORS): MINIMUM EGRESS WIDTH CALCULATIONS (STAIRS): NOT APPLICABLE 2 EXITS REQUIRED; 2 EXITS PROVIDED DOORS: 36" MIN. REQUIRED, 36" MIN. PROVIDED C O D E A N A L Y S I S RAMPS: NOT APPLICABLE AISLES: 36" MIN. REQUIRED, 36" PROVIDED CORRIDORS: 44" MIN. REQUIRED, 44" PROVIDED GENERAL INFORMATION GI002 BW/GS/RK SEAL: MARK DATE ISSUE --- PROJECT NO: PROJECT ARCHITECT: PROJECT MANAGER: DRAWN BY: DATE: COPYRIGHT: 17-055 REK REK 12/20/2017 SHEET TITLE: CONSULTANT: 64 GOTHIC STREET, SUITE 1 NORTHAMPTON, MA 01060 T 413.585.1512 F 413.586.7945 www.haiarchitecture.com H AI Architecture, Inc. Loan Servicing Department 1st Floor Florence Bank 85 Main Street Florence, MA 01062 Renovation for: PROJECT: REK REMOVE WALL COVERING WHERE PRESENT (WALLPAPER/ VINYL WALLCOVERING, ETC.) CLEAN AND PREPARE EXISTING SUBSTRATE AND PATCH HOLES AS REQUIRED TO FACILITATE INSTALLATION OF NEW FINISH AS SPECIFIED IN THE FINISH SCHEDULE. REMOVE EXISTING DOORS AND DOOR FRAMES AS SCHEDULED. PATCH AND REPAIR WALLS, FLOORS AND CEILINGS TO MATCH EXISTING AND NEW WORK AS SCHEDULED. RELOCATE AND REFINISH/RECONDITION DOORS THAT ARE SCHEDULED TO BE RELOCATED IN THE DOOR SCHEDULE. REMOVE EXISTING SUSPENDED ACOUSTICAL CEILING TILES, REPAIR GRID AS REQUIRED FOR NEW TILES. REMOVE EXISTING BASE (VINYL, TILE, CARPET, ETC.). CLEAN AND PREPARE THE EXISTING SUBSTRATE AS REQUIRED TO FACILITATE THE INSTALLATION OF NEW BASE. SEE ROOM FINISH SCHEDULE FOR NEW BASE TYPE. REMOVE EXISTING FLOOR COVERING (VINYL, TILE, RESILIENT SHEET ETC.); PATCH AND REPAIR FLOOR AS REQUIRED. CLEAN AND PREPARE THE EXISTING SUBSTRATE AS REQUIRED TO FACILITATE THE INSTALLATION OF NEW FLOOR COVERING. (SEE ROOM FINISH SCHEDULE FOR NEW FLOOR COVERING). NOTE: ALL FLOORS IN ROOMS OR AREAS THAT ARE SCHEDULED TO RECEIVE NEW FLOOR COVERING WILL HAVE THE EXISTING FLOOR COVERING REMOVED IN THAT AREA, UNLESS NOTED OTHERWISE. GENERAL CONTRACTOR TO INSURE THAT THE FLOOR IS LEVEL PRIOR TO INSTALLING NEW FLOORING. REMOVE EXISTING CABINET WORK, COUNTERS, SHELVING, EQUIPMENT AND OTHER BUILT - IN ITEMS AS SHOWN OR OTHERWISE CALLED OUT TO BE REMOVED. PATCH SURFACES AS REQUIRED TO RECEIVE NEW FINISH SURFACES. PROVIDE TEMPORARY DUSTPROOFING PARTITIONS AT ALL EXISTING AREAS THAT ABUT THE WORK AREA AND WHERE INDICATED ON THE DRAWINGS. TEMPORARY PARTITIONING SHALL BE LOCKABLE, AND SHALL EXTEND FROM FLOOR TO UNDERSIDE OF STRUCTURE ABOVE. SEE DRAWINGS FOR LOCATIONS. DEMOLITION LEGEND 1 REMOVE EXISTING INTERIOR WINDOW ASSEMBLIES INCLUDING INTERIOR TRIM AS SCHEDULED. PATCH AND REPAIR WALLS, FLOORS, AND CEILING TO MATCH EXISTING AND NEW WORK AS SCHEDULED. IN ALL AREAS WHERE DEMOLITION OCCURS COORDINATE WITH MEP TRADES FOR SPECIFICS IF HAZARDOUS MATERIALS ARE ENCOUNTERED DURING DEMOLITION OPERATIONS, IMMEDIATELY NOTIFY OWNER AND COMPLY WITH APPLICABLE REGULATIONS, LAWS, AND ORDINANCES CONCERNING REMOVAL, HANDLING AND PROTECTION AGAINST EXPOSURE OR ENVIRONMENTAL POLLUTION. REMOVE EXISTING STUD PARTITIONS, CMU OR BRICK OR PORTIONS OF SAME (INCLUDING ALL ELECTRICAL DEVICES AND WIRING, PLUMBING FIXTURES AND PIPING AND ANY OTHER ITEMS MADE OBSOLETE BY THE REMOVAL OF THE PARTITION), CHASES, DOORS, FRAMES AND MISCELLANEOUS CONSTRUCTION ITEMS. PATCH AND REPAIR WALLS, FLOORS, CEILINGS TO MATCH EXISTING AND NEW WORK AS SCHEDULED. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2A 12 14 17 16 13 15 THE FOLLOWING DEMOLITION NOTES REFER ONLY TO THE GENERAL SCOPE OF DEMOLITION REQUIRED TO COMPLETE THIS PROJECT, AND MAY NOT SPECIFICALLY IDENTIFY EACH AND EVERY COMPONENT OF AN ARCHITECTURAL, MECHANICAL, OR ELECTRICAL SYSTEM OR ASSEMBLY (WHETHER DESIGNATED ON THE DEMOLITION PLAN (S) OR NOT). THE GENERAL CONTRACTOR AND HIS/HER SUBCONTRACTORS SHALL BE REQUIRED TO REMOVE/DEMOLISH INCIDENTAL ITEMS THAT MAY BE CONSTRUED TO BE RELEVANT TO THE SCOPE OF DEMOLITION SHOWN ON THE DEMOLITION PLAN(S), OR REQUIRED TO COMPLETE THE NEW WORK. THE GENERAL CONTRACTOR SHALL BE REQUIRED TO DEMOLISH SPECIFIC ITEMS, WHETHER OR NOT THEY ARE SPECIFICALLY INDICATED. THE GENERAL CONTRACTOR SHALL BE REQUIRED TO CUT ALL HOLES IN FLOORS, WALLS, CEILINGS, ETC. AS REQUIRED FOR MECHANICAL OR ELECTRICAL WORK IDENTIFIED IN THE CONTRACT DOCUMENTS (INCLUDING, BUT NOT LIMITED TO DUCTWORK, HYDRONIC PIPING, FIRE SUPPRESSION PIPING, PLUMBING PIPING, AND/OR ELECTRICAL CONDUIT FOR POWER / DATA / LOW VOLTAGE / SPECIALTY SYSTEMS). GENERALLY, THESE PENETRATIONS ARE NOT SHOWN ON THE CONTRACT DRAWINGS; HOWEVER, THE GENERAL CONTRACTOR (OR APPROPRIATE SUBCONTRACTOR) SHALL BE RESPONSIBLE FOR CORING OPERATIONS, AND SLEEVING PENETRATIONS WHERE REQUIRED, WITH A MATERIAL THAT IS SUITED TO THE TYPE OF PENETRATION AND RATING OF THE ASSEMBLY BEING PENETRATED. THE GENERAL CONTRACTOR SHALL BE REQUIRED TO PATCH AND REPAIR ALL DAMAGED SURFACES TO MATCH EXISTING AND/OR AS REQUIRED BY THE NEW WORK. DEMOLITION NOTES DEMOLITION KEY NOTES DEMOLITION EXISTING CONSTRUCTION TEMPORARY DUSTPROOFING PARTITIONS X TP TP UP TOILET CLOSET 005 OPEN OFFICE 001 OFFICE 002 OFFICE 003 OFFICE 004 OFFICE 006 CORRIDOR 007 F F F P F SLIDING SHELVING STORAGE SLIDING SHELVING STORAGE RAD.DN RECEPTION 103 OFFICE SPACE/ CUBICLES 105 OFFICE OFFICE 111 FILING/ STORAGE I.T. 109 CONFERENCE 104 ENTRY VESTIBULE 102 NOTE: RENO IN VESTIBULE INCLUDES UPDATING FINISHES UP D.F. TOILET PROJECT AREA A.P. A.P. A.P. A.P. RADIATOR RAD. LOBBY 101 OFFICE SPACE/ CUBICLES 108 AISLE 110 2 2 2 8 4 4 9 REMOVE SLIDING SHELVING SYSTEMS & RISERS- COORDINATE W/ OWNER. PATCH & REPAIR FLOOR AS REQUIRED. REMOVE SLIDING SHELVING SYSTEM & RISER- COORDINATE W/ OWNER. PATCH & REPAIR FLOOR AS REQUIRED. REMOVE RECEPTION DESK- COORDINATE W/ OWNER REMOVE CUBICLES/ DESKS- COORDINATE W/ OWNER 5 6 7 7 6 5 6 (CARPET FLOOR & BASE) 5 6 (CARPET FLOOR & BASE) 5 6 (CARPET FLOOR & BASE) 5 6 (CARPET FLOOR & BASE) 5 6 (CARPET FLOOR & BASE) 5 6 (ADJUSTABLE SHELVES) 5 6 (CARPET FLOOR & BASE) 5 6 (CARPET FLOOR / VINYL BASE) REMOVE DESK- COORDINATE W/ OWNER 4 4 (COAT HOOKS SHELF) 10 10 10 5 10 10 10 10 10 3 3 3 2 3 DEMOLITION PLAN SCALE: 1/4" = 1'-0" DEMOLITION PLAN AD101 BW/GS/RK SEAL: MARK DATE ISSUE --- PROJECT NO: PROJECT ARCHITECT: PROJECT MANAGER: DRAWN BY: DATE: COPYRIGHT: 17-055 REK REK 12/20/2017 SHEET TITLE: CONSULTANT: 64 GOTHIC STREET, SUITE 1 NORTHAMPTON, MA 01060 T 413.585.1512 F 413.586.7945 www.haiarchitecture.com H AI Architecture, Inc. Loan Servicing Department 1st Floor Florence Bank 85 Main Street Florence, MA 01062 Renovation for: PROJECT: SUSPENDED ACOUSTICAL CEILING REFLECTED CEILING PLAN LEGEND 2'x4' LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS 2'x2' LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS RECESSED DOWNLIGHT FIXTURE - SEE ELECTRICAL DRAWINGS 1'x4' SURFACE MOUNTED LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS CEILING MOUNTED EXIT SIGN - SEE ELECTRICAL DRAWINGS WALL MOUNTED EXIT SIGN - SEE ELECTRICAL DRAWINGS 1'x4' LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS SPRINKLER HEAD - SEE FIRE PROTECTION DRAWINGS GYPSUM BOARD CEILING / SOFFIT SUPPLY DIFFUSER - SEE HVAC DRAWINGS RETURN OR EXHAUST GRILLE - SEE HVAC DRAWINGS S CEILING MOUNTED SPEAKER - SEE ELECTRICAL DRAWINGS 2' UNDERCABINET LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS 4' UNDERCABINET LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS BOX SOFFIT ABOVE CABINETRY EXISTING TO REMAINE RELOCATE EXISTING DEVICE / FIXTURERL LOCATION OF RELOCATED DEVICE / FIXTURENL PLASTIC LAMINATE CEILING / SOFFIT CEILING MOUNTED SMOKE DETECTOR HF F S CEILING MOUNTED HEAT DETECTOR DEMOLITION REFLECTED CEILING DEMOLITION PLAN SCALE: 1/4" = 1'-0" UP TOILET CLOS 005 OPEN OFFICE 001 OFFICE 002 OFFICE 003 OFFICE 004 OFFICE 006 CORRIDOR 007 DN RECEPTION 103 OFFICE SPACE/ CUBICLES 105 OFFICE 111 I.T. 109 CONFERENCE 104 ENTRY VESTIBULE 102 UP TOILET PROJECT AREA SUPERVISOR OFFICE 107OFFICE 112 OFFICE 106 LOBBY 101 OFFICE SPACE/ CUBICLES 108 AISLE 110 SEC F F F F SEC F S F S F S F S F S F S REMOVE EXISTING CROWN MOLDING DEMOLITION REFLECTED CEILING PLAN AD102 GS/RK SEAL: MARK DATE ISSUE --- PROJECT NO: PROJECT ARCHITECT: PROJECT MANAGER: DRAWN BY: DATE: COPYRIGHT: 17-055 REK REK 12/20/2017 SHEET TITLE: CONSULTANT: 64 GOTHIC STREET, SUITE 1 NORTHAMPTON, MA 01060 T 413.585.1512 F 413.586.7945 www.haiarchitecture.com H AI Architecture, Inc. Loan Servicing Department 1st Floor Florence Bank 85 Main Street Florence, MA 01062 Renovation for: PROJECT: UP TOILET CLOSET 005 OPEN OFFICE 001 OFFICE 002 OFFICE 003 OFFICE 004 OFFICE 006 CORRIDOR 007 F F F P F RECEPTION DESKRAD.DN RECEPTION 103 OFFICE SPACE/ CUBICLES 105 OFFICE 111 I.T. 109 CONFERENCE 104 ENTRY VESTIBULE 102 NOTE: RENO IN VESTIBULE INCLUDES UPDATING FINISHES UP D.F. TOILET PROJECT AREA SUPERVISOR OFFICE 107 107 RADIATOR RAD. 106 OFFICE 112 1'-0" CLEAR8'-138rF.V.10'-812" 4'-0"5'-112"F.V.10'-9 316"4'-8 5 16r (4'-8" MIN.) q 105 1 1 1 5 11 3 4 1 1 1 1 2 r F.V. 5'-5" CLEAR 1 11'-312"9'-818r 4'-8"10'-412" V.I.F.6'-5"26'-212rF.V.112 3 OFFICE 106 LOBBY 101 OFFICE SPACE/ CUBICLES 108 AISLE 110 104 2 11'-7116r F.V. ALIGN3'-8"CLEAR3'-8"5'-318"5'-038"9'-01 4"12'-73 8" ALIGN 2'-0"2'-0"5'-0"6'-612" ALIGN 1'-0"4'-1516rF.V.1'-0"1'-0"1'-10" CL 1'-10"CL 3'-8"CLEAR7'-514rF.V.A 13 A501 D 13 A501 FLOOR PLAN SCALE: 1/4" = 1'-0" LEGEND ROOM NAME AND ROOM NUMBER WALL TYPE ROOM NAME XXX DOOR NUMBERXXX NEW WALL CONSTRUCTION EXISTING CONSTRUCTION NEW HALF WALL CONSTRUCTION (U.N.O.) NEW MILLWORK / CASEWORK WITH PLASTIC LAMINATE COUNTERTOP NEW MILLWORK / CASEWORK WITH SOLID SURFACE COUNTERTOP 1 PROJECT AREA KEY PLAN SCALE: NOT TO SCALE 20 A101 DN 1. GENERAL CONTRACTOR MUST VERIFY ALL CONDITIONS AND DIMENSIONS AT THE JOB SITE AND REPORT ANY DISCREPANCIES TO ARCHITECT BEFORE PROCEEDING WITH THE WORK. 2. ANY REPAIRS, PATCHING, OR DEMOLITION INDICATED ON DRAWINGS REPRESENT THE GENERAL AREA WHERE WORK IS TO BE DONE, BUT DOES NOT NECESSARILY LIMIT THE EXTENT OF WORK. THE GENERAL CONTRACTOR IS RESPONSIBLE FOR ALL SUCH REPAIRS, PATCHING, ETC. WHERE THEY OCCUR IN BUILDING UNDER THIS CONTRACT. 3. PROVIDE TEMPORARY DUST PROOFING PARTITIONS TO EFFECTIVELY SEAL OFF WORK AREAS FROM THE REST OF THE BUILDING. PROVIDE TEMPORARY DOOR IF NECESSARY. TEMPORARY PARTITIONS SUBJECT TO APPROVAL OF OWNER AND ARCHITECT. 4. REPAIR ANY IRREGULARITIES IN SURFACES INCLUDING BUT NOT LIMITED TO AREAS DISTURBED BY NEW WORK. EXISTING SURFACES INCORPORATED INTO NEW WORK SHALL BE REPAIRED AND RE-FINISHED TO THE SAME STANDARD AS NEW WORK. 5. CONSTRUCT NEW INTERIOR PARTITIONS FROM FLOOR TO THE BOTTOM OF THE STRUCTURE (DECK OR SLAB) ABOVE UNLESS NOTED OTHERWISE VERIFY IN FIELD. 6. ALL WORK TO BE CONSIDERED AS NEW WORK UNLESS INDICATED AS EXISTING TO REMAIN. 7. WHERE UTILITY AND MECHANICAL WORK IS REMOVED OR ALTERED, GENERAL CONTRACTOR IS RESPONSIBLE FOR PREPARING AND PATCHING BUILDING STRUCTURE TO MATCH NEW AND EXISTING WORK AS INDICATED ON DRAWINGS. 8. GENERAL CONTRACTOR TO PROVIDE BLOCKING AS REQUIRED FOR ALL WALLS, NEW OR EXISTING, THAT ARE TO RECEIVE NEW OR EXISTING CABINETRY, SHELVING, ETC. 9. ALL DOORS AND WALLS NOT LABELED WITH A WALL TYPE OR DOOR NUMBER ARE TO BE CONSIDERED EXISTING TO REMAIN. 10. FURNITURE SHOWN ON DRAWINGS, EXCEPT CASEWORK, IS NOT INCLUDED IN THIS CONTRACT UNLESS NOTED OTHERWISE. 11. DIMENSIONS ARE TAKEN FROM FACE OF FINISHED CONSTRUCTION. CLEAR DIMENSIONS ARE TO FINISHED FACE OF CONSTRUCTION AND SHALL TAKE PRECEDENCE OVER ANY OTHER DIMENSION. GENERAL CONSTRUCTION NOTES SEAL: MARK DATE ISSUE --- PROJECT NO: PROJECT ARCHITECT: PROJECT MANAGER: DRAWN BY: DATE: COPYRIGHT: 17-055 REK REK 12/20/2017 SHEET TITLE: CONSULTANT: 64 GOTHIC STREET, SUITE 1 NORTHAMPTON, MA 01060 T 413.585.1512 F 413.586.7945 www.haiarchitecture.com H AI Architecture, Inc. Loan Servicing Department 1st Floor Florence Bank 85 Main Street Florence, MA 01062 Renovation for: PROJECT: FLOOR PLAN A101 BW/GS/RK SUSPENDED ACOUSTICAL CEILING REFLECTED CEILING PLAN LEGEND 2'x4' LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS 2'x2' LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS RECESSED DOWNLIGHT FIXTURE - SEE ELECTRICAL DRAWINGS 1'x4' SURFACE MOUNTED LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS CEILING MOUNTED EXIT SIGN - SEE ELECTRICAL DRAWINGS WALL MOUNTED EXIT SIGN - SEE ELECTRICAL DRAWINGS CEILING TRACK AND CURTAINS 1'x4' LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS SPRINKLER HEAD - SEE FIRE PROTECTION DRAWINGS SECURITY CAMERA - SEE ELECTRICAL DRAWINGS GYPSUM BOARD CEILING / SOFFIT SUPPLY DIFFUSER - SEE HVAC DRAWINGS RETURN OR EXHAUST GRILLE - SEE HVAC DRAWINGS S CEILING MOUNTED SPEAKER - SEE ELECTRICAL DRAWINGS 2' UNDERCABINET LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS 4' UNDERCABINET LIGHT FIXTURE - SEE ELECTRICAL DRAWINGS BOX SOFFIT ABOVE CABINETRY EXISTING TO REMAINE RELOCATE EXISTING DEVICE / FIXTURERL LOCATION OF RELOCATED DEVICE / FIXTURENL PLASTIC LAMINATE CEILING / SOFFIT MEP WORK TO BE DESIGN BUILD CEILING TYPE CEILING HEIGHT ABOVE FINISH FLOOR EXISTING CEILING GRID TO REMAIN - REPLACE CEILING TILES REFLECTED CEILING PLAN KEYED NOTES CEILING MOUNTED SMOKE DETECTOR DOME LIGHT WITH AUDIBLE LOCAL ALARM HF F S CEILING MOUNTED HEAT DETECTOR USG MARS CLIMA PLUS #86785, 24"x24" TEGULAR TILE, COLOR: WHITE (FOR EXISTING 15/16" TEE GRID SYSTEM) CEILING TYPE SCHEDULE TYPE 1A MODIFY EXISTING CEILING AS REQUIRED BY NEW WORK - REPAIR GRID AS NECCESSARY WHERE EXISTING PARTITIONS TO UNDERSIDE OF GRID ARE REMOVED 1 2 3 SECOR 1.ALL NEW SPRINKLER HEADS TO BE CENTERED IN THE NEW CEILING GRID SYSTEM. (COORDINATE LOCATIONS WITH FIRE PROTECTION PLAN AND ALL OTHER TRADES). 2.COORDINATE NEW CEILING WORK WITH ALL NEW AND EXISTING CEILING ITEMS, ACCESSORIES AND SYSTEMS. 3.SEE H.V.A.C. DRAWINGS FOR ALL NEW EXHAUST GRILLES AND DIFFUSERS, COORDINATE ALL NEW DIFFUSERS WITH NEW CEILING GRID LAYOUT, LIGHTS, SPEAKERS, SPRINKLERS, ETC.... 4.CENTER ALL NEW ACOUSTICAL CEILING TILES IN BOTH DIMENSIONS IN ALL ROOMS SCHEDULED TO RECEIVED NEW SUSPENDED ACOUSTICAL TILE UNLESS SHOWN DIFFERENTLY ON DRAWINGS. 5.SEE ELECTRICAL LIGHTING PLAN AND SCHEDULE FOR ALL LIGHTING FIXTURES. 6.ALL NEW SMOKE AND HEAT DETECTORS SHALL BE CONNECTED TO THE EXISTING FIRE ALARM SYSTEM. 7.ALL SUSPENDED CEILINGS SHALL BE EQUIPPED WITH RETENTION CLIPS AT NEW TILE (I. E. @ ENTRANCE VESTIBULES, LOBBIES, ALL CORRIDORS THAT LEAD DIRECTLY TO THE EXTERIOR, AND THROUGHOUT ALL BEHAVIORAL HEALTH PROJECTS). 8.USE HARDWARE FRIENDLY OPTIONS AT ALL LIGHT FIXTURES AND OTHER ACCESSORIES. GAPS BETWEEN FIXTURE TRIM AND REVEALS ARE NOT ACCEPTABLE. CEILING NOTES EXISTING SOFFIT TO REMAIN UP TOILET CLOS 005 OPEN OFFICE 001 OFFICE 002 OFFICE 003 OFFICE 004 OFFICE 006 CORRIDOR 007 DN RECEPTION 103 OFFICE SPACE/ CUBICLES 105 OFFICE 111 I.T. 109 CONFERENCE 104 ENTRY VESTIBULE 102 UP TOILET PROJECT AREA SUPERVISOR OFFICE 107OFFICE 112 OFFICE 106 LOBBY 101 OFFICE SPACE/ CUBICLES 108 AISLE 110 REFLECTED CEILING PLAN SCALE: 1/4" = 1'-0" SEC F F F F SEC F S F S F S 2 2 2 2 2 3 33 RELOCATE EXISTING HVAC GRILL 1 1 1 1 11 1 1 3 3 NEW CROWN MOLDING TO MATCH EXISTING AT THREE WALLS. RETURN ENDS AT EXISTING STOREFRONT F S RELOCATE EXISTING SMOKE DETECTOR NEW SPRINKLER HEAD NEW EXIT SIGN MATCH EXISTING F S RELOCATE EXISTING SMOKE DETECTOR NEW EXIT SIGN MATCH EXISTING RELOCATE EXISTING SPRINKLER HEAD RELOCATE EXISTING SPRINKLER HEAD F S RELOCATE EXISTING EXIT SIGN REFLECTED CEILING PLAN A102 BW/GS/RK SEAL: MARK DATE ISSUE --- PROJECT NO: PROJECT ARCHITECT: PROJECT MANAGER: DRAWN BY: DATE: COPYRIGHT: 17-055 REK REK 12/20/2017 SHEET TITLE: CONSULTANT: 64 GOTHIC STREET, SUITE 1 NORTHAMPTON, MA 01060 T 413.585.1512 F 413.586.7945 www.haiarchitecture.com H AI Architecture, Inc. Loan Servicing Department 1st Floor Florence Bank 85 Main Street Florence, MA 01062 Renovation for: PROJECT: 1. COORDINATE WITH OWNER FOR ACCENT PAINT LOCATIONS. FINISH SCHEDULE NOTES FINISH MATERIALS KEY KEY MATERIAL MANUFACTURER SERIES NUMBER COLOR 2. BORDER CARPET C3 SHALL BE 1'-0" WIDE AND SHALL BE INSTALLED IN MONOLITHIC PATTERN. 101 LOBBY WALLCOVERINGPAINTWALLCOVERINGPAINTPAINTSTAIN & VARNISHCARPETBORDER CARPETCARPET BASEPAINTEXISTING METAL TO REMAINROOM FINISH SCHEDULE ROOM #ROOM NAME FLOOR BASE WALLS DOOR TRIM REMARKS WESTSOUTH WALLCOVERINGPAINTEAST WALLCOVERINGNORTH C4 -PAINT--- C1 BROADLOOM CARPET MASLAND RHYTHYM 18608 TIME C4 P1 PAINT-WALL BENJAMIN MOORE 1069 TWILIGHT GOLD P2 BENJAMIN MOORE HC-77 ALEXANDRIA BEIGE 102 ENTRY VESTIBULE 103 104 105 106 107 OFFICE RECEPTION CONFERENCE OPEN OFFICE / CUBICLES OFFICE C2 CARPET TILE C3 CARPET TILE SHAW RADIANCE 60755 NATURAL TONIC J & J INVISION PULP 453 STENCIL J & J INVISION MESH BROADLOOM 453 STENCILBROADLOOM CARPET C4 C4 C4 C4 C4 C4 C5 C3C2 C3C2 C3C2 P3 BENJAMIN MOORE 1624 WESTCOTT NAVYP4 PAINT-DOOR BENJAMIN MOORE 1038 EVERLASTING - - - - PAINT-WALL PAINT-WALL P1 3. OFFICE CARPET C2 SHALL BE INSTALLED IN ASHLAR PATTERN. P1 P1 P1 P4 P3 P3 P3 P3 P3 P3 P4 P1 P3 P1 P1 P3 P3 P1 P3 P3P3 P3 P3 X P2 P2 108 109 IT CLOSET OPEN OFFICE / CUBICLES 110 111 112 AISLE OFFICE OFFICE C3C2 C3C2 C1 C1 C3C2 C1 C5 (FROM OWNER'S ATTIC STOCK)-BROADLOOM CARPET -- SOLID SURFACE CORIAN --SS1 NEVAMAR --L1 - - - PLASTIC LAMINATE DOOR NOTES ABBREVIATIONS DOORDR HOLLOW METALHM INSULATED HOLLOW METALIHM KICKPLATE (HEIGHT")K(12) MTL.METAL MIN MINERAL CORE PTD.PAINTED SCW SOLID CORE WOOD S.S.STAINLESS STEEL STL.STEEL TI TEMPERED INSULATED V.I.F.VERIFY IN FIELD WD.WOOD ALUMINUMAL T TEMPERED 1/4" WG 1/4" WIRE GLASS 1/4" T 1/4" TEMPERED GLASS 1" IG 1" INSULATED GLASS ANODIZED ALUMINUMAA EI VINYL CLAD DOOR NOTE: 1. ALL DOOR HANDLES SHALL BE OF LEVER TYPE MEETING CURRENT ADA STANDARDS, (AS NOTED IN THE HARDWARE SCHEDULE). DOOR HANDLES TO ROOMS CONSTITUTING A HAZARD (ELECTRICAL ROOMS, MECHANICAL ROOMS, SOILED UTILITY ROOMS, ETC.) SHALL BE LEVER TYPE WITH A KNURLED FINISH ON THE GRIP SURFACE. 2. ALL LOCKSETS & LATCHSETS SHALL BE OF MORTISE DESIGN. 3. ALL HARDWARE FINISH SHALL BE BRUSHED STAINLESS STEEL (US32D). 4. ALL PRODUCTS SPECIFIED ON AN 'OR EQUAL' BASIS UNLESS OTHERWISE NOTED. 5. PROVIDE REQUIRED POWER SUPPLY SYSTEMS FOR OPERATING ALL ELECTROMAGNETIC LOCKS, ELECTROMECHANICAL LOCKS, ELECTRIC STRIKES, & MARLOK ELECTRONIC CYLINDER SYSTEMS. COORDINATE REQUIREMENTS WITH E.C. 6. ALL ELECTROMAGNETIC LOCKS, ELECTROMECHANICAL LOCKS, & ELECTRIC STRIKES SHALL BE OF THE 'FAIL SAFE' DESIGN, UNLOCKING WHEN THE FIRE ALARM IS ACTIVATED OR ELECTRICAL POWER IS INTERRUPTED. 7. ALL STAINLESS STEEL KICKPLATES SHALL BE 2" LESS THAN DOOR WIDTH x 12" HIGH (TYPICAL - U.O.N.) AND SHALL BE MOUNTED 1" FROM THE BOTTOM OF THE DOOR; SEE SPECIFICATION. 8. ALL HOLLOW METAL FRAMES SHALL BE SHOP WELDED UNLESS NOTED OTHERWISE. 9. SPECIES OF ALL DOORS SHALL MATCH EXISTING. DOOR SCHEDULE MARK LBLMATL DOOR SIZEELEV HDWR DOOR FRAME LBLMATLTRANSITIONJAMB DETAILLFSGLAZHEAD REMARKS 105 -SCW3'-0"x 7'-0"x 1-3/4"A T -1 HM9B/A50110/A501 2 (SEE DOOR NOTES) - 106 -SCW3'-0"x 7'-0"x 1-3/4"A T -1 HM 1 - 107 -SCW3'-0"x 7'-0"x 1-3/4"A T -1 HM 1 - 112 -SCW3'-0"x 7'-0"x 1-3/4"A T -1 HM 1 - HARDWARE SCHEDULE 1.1-1/2 PAIR BUTT HINGES, BALL BEARING 1 - OFFICE LOCKSET WITH LEVER HANDLES 1 - DOOR STOP, WALL OR FLOOR MOUNT 1 - SET DOOR MUTES 10/A501 10/A501 10/A501 10/A501 10/A501 10/A501 10/A501 2.1-1/2 PAIR BUTT HINGES, BALL BEARING 1 - OFFICE LOCKSET WITH LEVER HANDLES 1 - DOOR STOP, WALL OR FLOOR MOUNT 1- CLOSER 1 - SET DOOR MUTES 1 - STAINLESS STEEL KICKPLATE (PUSH SIDE) TO MATCH EXISTING P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P1 P3P3 P3 P3 P3P3 P3 P3 X X X P2 P2 P2 9B/A501 9B/A501 9B/A501 1 WALL TYPE SCALE: 1" = 1'-0" NON-RATED WALL FLOOR LINE 5/8" TYPE "X" GYPSUM BOARD (EACH SIDE) 3-5/8" METAL STUDS @ 16" O.C. BATT SOUND INSULATION DIA. BRACING 3-5/8"x 18GA, ALONG LENGTH OF PARTITION @8'-0" O.C. TO STRUCTURE ABOVE SECURE TO STRUCTURE @ EACH END EACH CONNECTION BASE - SEE ROOM FINISH SCHEDULE CEILING SEE R.C.P. LINE OF STRUCTURAL DECK OR SLAB ABOVE SECURE TOP TRACK TO EXISTING CEILING GRID WITH CADDY CLIPS USE MOISTURE RESISTANT GYPSUM BOARD FOR ALL WET AREAS EXISTING WALL CONSTRUCTION TO REMAIN 7/8" METAL FURRING HAT CHANNEL @ 24" O.C. 5/8" TYPE "X" GYPSUM BOARD FLOOR LINE BASE - SEE ROOM FINISH SCHEDULE 2 WALL TYPE SCALE: 1" = 1'-0" CEILING SEE R.C.P. LINE OF STRUCTURAL DECK OR SLAB ABOVE NON-RATED WALL USE MOISTURE RESISTANT GYPSUM BOARD FOR ALL WET AREAS FLOOR LINE 5/8" TYPE "X" GYPSUM BOARD (EACH SIDE) 3-5/8" METAL STUDS @ 16" O.C. FASTEN PLATE SECURELY TO FLOOR NOTE: FASTEN ONE END OF WALL TO EXISTING WALL. PROVIDE BLOCKING AND SUPPORT AS REQUIRED4'-0"N.T.S.BASE - SEE ROOM FINISH SCHEDULE 3/4" SOLID SURFACE CAP WITH 1/4" SOLID SURFACE REVEAL - SEE ROOM FINISH SCHEDULE1/4"1/4" 3 WALL TYPE SCALE: 1" = 1'-0" METAL CORNER BEAD (TYP.) 10 GA. WALL SUPPORT FRAMING REINFORCEMENT UNIT - 3.625" x 24" SECURED TO FLOOR WITH 1/2" ACCESSORY PLATE AND (2) 3/8" DIA. EXPANSION ANCHORS, 3-1/2" EMBEDMENT. UNITS AT ADJACENT TWO STUDS AT END OF WALL AND @32" O.C. 5/8" TYPE "X" GYPSUM BOARD (EACH SIDE) 3-5/8" METAL STUDS @ 16" O.C. FASTEN PLATE SECURELY TO FLOOR NOTE: FASTEN ONE END OF WALL TO EXISTING WALL. PROVIDE BLOCKING AND SUPPORT AS REQUIRED2'-10"3/4" SOLID SURFACE CAP WITH 1/4" SOLID SURFACE REVEAL - SEE ROOM FINISH SCHEDULE1/4"1/4" 4 WALL TYPE SCALE: 1" = 1'-0" METAL CORNER BEAD (TYP.) 10 GA. WALL SUPPORT FRAMING REINFORCEMENT UNIT - 3.625" x 24" SECURED TO FLOOR WITH 1/2" ACCESSORY PLATE AND (2) 3/8" DIA. EXPANSION ANCHORS, 3-1/2" EMBEDMENT. UNITS AT ADJACENT TWO STUDS AT END OF WALL AND @32" O.C. FURNITURE - SEE FURNITURE PLAN 1'-0"1"3"2'-0"2"4"1/2" x 4" x 4" ALUMINUM BRACKET @ 36" O.C. 24"H x PLASTIC LAMINATE PANELS WITH 1" REVEALS PLASTIC LAMINATE THIS FACE OF WALL 5 WALL TYPE SCALE: 1" = 1'-0" FLOOR LINE BASE - SEE ROOM FINISH SCHEDULE 5/8" TYPE "X" GYPSUM BOARD (EACH SIDE) 3-5/8" METAL STUDS @ 16" O.C. FASTEN PLATE SECURELY TO FLOOR NOTE: FASTEN ONE END OF WALL TO EXISTING WALL. PROVIDE BLOCKING AND SUPPORT AS REQUIRED3'-8"3/4" SOLID SURFACE CAP WITH 1/4" SOLID SURFACE REVEAL - SEE ROOM FINISH SCHEDULE 10 GA. WALL SUPPORT FRAMING REINFORCEMENT UNIT - 3.625" x 24" SECURED TO FLOOR WITH 1/2" ACCESSORY PLATE AND (2) 3/8" DIA. EXPANSION ANCHORS, 3-1/2" EMBEDMENT. UNITS AT ADJACENT TWO STUDS AT END OF WALL AND @32" O.C. FURNITURE - SEE FURNITURE PLAN 1'-0"1"3"2'-10"2"4"1/2" x 4" x 4" ALUMINUM BRACKET @ 36" O.C. 34"H x PLASTIC LAMINATE PANELS WITH 1" REVEALS PLASTIC LAMINATE THIS FACE OF WALL FLOOR LINE BASE - SEE ROOM FINISH SCHEDULE SEE WALL TYPE 4 CARPET - SEE ROOM FINISH SCHEDULE1/2"MAXIMUMUNDERCUTCARPET - SEE ROOM FINISH SCHEDULE CL DOOR (SHOWN IN CLOSED POSITION) - SEE DOOR SCHEDULE; SEE SPEC. (TYP.) DOOR TRANSITION DETAIL SCALE: 6" = 1'-0" 9B A501 HOLLOW METAL FRAME - PAINT; SEE SPEC. (TYP.) CAULK CONT. (BOTH SIDES) 2x WOOD BLOCKING (FIRE -RETARDANT) SEE FLOOR PLAN FOR WALL TYPE 12" TYP.2"12"WALL ANCHORS & BASE CLIPS DOOR - SEE DOOR SCHEDULE DOOR HEAD / JAMB DETAIL SCALE: 3" = 1'-0" 10 A501 DOOR ELEVATIONS 24"x36" TEMPERED VISION PANEL IN PAINTED H.M. FRAME SEE SCHED. A 6" TYP.10"2"TYP.SEE SCHED.2" TYP. 2" TYP. RECEPTION #103 INTERIOR ELEVATION SCALE: 1/4" = 1'-0" 13 A101 BASE - SEE ROOM FINISH SCHEDULE A 3'-8"6'-612r F.V. 1" 1'-638" 1" 1'-638" 1" 1'-638" 1" 1'-638" 1"4"2'-10"6"34"H x PLASTIC LAMINATE PANELS WITH 1" REVEALS - SEE WALL TYPE 5/A501 OPEN LOW WALL - SEE WALL TYPE 3/A501 D 1" 1'-3" 1" 1'-314" 1" 1'-3" 1" OPEN 4"2'-0"6"2'-10"24"H x PLASTIC LAMINATE PANELS WITH 1" REVEALS - SEE WALL TYPE 4/A501 INTERIOR ELEVATIONS, WALL TYPES, DOOR AND ROOM FINISH SCHEDULE A501 GS SEAL: MARK DATE ISSUE --- PROJECT NO: PROJECT ARCHITECT: PROJECT MANAGER: DRAWN BY: DATE: COPYRIGHT: 17-055 REK REK 12/20/2017 SHEET TITLE: CONSULTANT: 64 GOTHIC STREET, SUITE 1 NORTHAMPTON, MA 01060 T 413.585.1512 F 413.586.7945 www.haiarchitecture.com H AI Architecture, Inc. Loan Servicing Department 1st Floor Florence Bank 85 Main Street Florence, MA 01062 Renovation for: PROJECT: UP TOILET CLOSET 005 OPEN OFFICE 001 OFFICE 002 OFFICE 003 OFFICE 004 OFFICE 006 CORRIDOR 007 F F F P F RAD.DN RECEPTION 103 OFFICE SPACE/ CUBICLES 105 OFFICE 111 I.T. 109 CONFERENCE 104 ENTRY VESTIBULE 102 UP D.F. TOILET PROJECT AREA A.P. A.P. A.P. A.P. SUPERVISOR OFFICE 107 RADIATOR RAD. OFFICE 112 4'-0"3'-6"6'-11"5'-1"3'-0"4'-7" 3'-2"2'-8"3'-5" 3'-3"2'-11"4'-4"3'-212"4'-0"4'-6"OFFICE 106 LOBBY 101 OFFICE SPACE/ CUBICLES 108 AISLE 110 FLOOR PLAN SCALE: 1/4" = 1'-0" FURNITURE PLAN AF101 BW/GS SEAL: MARK DATE ISSUE --- PROJECT NO: PROJECT ARCHITECT: PROJECT MANAGER: DRAWN BY: DATE: COPYRIGHT: 17-055 REK REK 12/20/2017 SHEET TITLE: CONSULTANT: 64 GOTHIC STREET, SUITE 1 NORTHAMPTON, MA 01060 T 413.585.1512 F 413.586.7945 www.haiarchitecture.com H AI Architecture, Inc. Loan Servicing Department 1st Floor Florence Bank 85 Main Street Florence, MA 01062 Renovation for: PROJECT: 1.ANY EXISTING MECHANICAL, ELECTRICAL, PLUMBING AND/OR FIRE PROTECTION DEVICES (THERMOSTATS, OUTLETS, SWITCHES, PULL STATIONS, ETC.) WITHIN WALLS SCHEDULED FOR DEMOLITION BUT REQUIRED TO REMAIN SHALL BE RELOCATED TO NEAREST ADJACENT WALL AS REQUIRED BY OWNERS, ARCHITECT AND / OR DESIGN/BUILD CONTRACTORS. 1.GENERAL NOTES A. THE PLANS ARE DIAGRAMMATIC IN NATURE AND THEIR INTENT IS TO SHOW THE BASIC REQUIREMENTS OF THE SYSTEM. THE INSTALLER SHALL FURNISH ALL MATERIALS, FIXTURES, WIRING, DEVICES, SUPPORT, DISCONNECT SWITCHES, AND OTHER REQUIRED EQUIPMENT NOT SPECIFICALLY INDICATED HEREIN, AND LABOR FOR A COMPLETE AND OPERATING SYSTEM AS SPECIFIED HEREIN. THE INSTALLER IS RESPONSIBLE FOR OBTAINING AND PAYING FOR ANY NECESSARY PERMITS AND APPROVALS, AND ANY OTHER CHARGES OR FEES. B.ALL ELECTRICAL WORK SHALL BE COMPLETED IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE (NFPA 70), AND THE THE MASSACHUSETTS ELECTRIC CODE. C.CONTRACTOR SHALL GUARANTEE ALL LABOR AND MATERIALS FOR A PERIOD OF ONE (1) YEAR FROM THE DATE OF SUBSTANTIAL COMPLETION. D.DO NOT SCALE DRAWINGS. SEE ARCHITECTURAL PLANS FOR EXACT LOCATIONS OF EQUIPMENT. ITEMS WHICH ARE NOT SPECIFICALLY LOCATED BY DIMENSION ON THE ARCHITECTURAL PLANS SHOULD BE COORDINATED WITH THE ARCHITECT. E.ALL EQUIPMENT LISTED ON THE DRAWING IS SPECIFIED AS "OR APPROVED EQUAL" UNLESS INDICATED OTHERWISE. THE CONTRACTOR SHALL PROVIDE SUBMITTALS FOR ANY EQUIPMENT DIFFERENT FROM WHAT IS LISTED ON THE DRAWINGS FOR APPROVAL BY THE ARCHITECT PRIOR TO INSTALLATION. FOR GENERAL EQUIPMENT WHICH IS NOT LISTED ON THE DRAWINGS, SUBMITTALS ARE REQUIRED AS OUTLINED IN THE SPECIFICATIONS. F.FOR EQUIPMENT FURNISHED BY "OTHERS", THE ELECTRICAL CONTRACTOR SHALL RUN THE POWER LINES TO EQUIPMENT DISCONNECT SWITCHES AND MAKE FINAL CONNECTION TO EQUIPMENT UNLESS INDICATED OTHERWISE. THE CONTROLS FOR SAID EQUIPMENT SHALL BE THE RESPONSIBILITY OF "OTHERS" UNLESS NOTED OTHERWISE. COORDINATE LOADS WITH OTHER TRADES AND VERIFY SAME. 2.WIRING A.ALL WIRING SHALL MATCH EXISTING BUILDING STANDARD UNLESS SPECIFICALLY INDICATED OTHERWISE. ALL WIRING TO BE IN ACCORDANCE WITH NATIONAL ELECTRIC CODE & MASS ELECTRIC CODE. ALL WIRING TO BE RUN CONCEALED. IN MOST CASE NEW LIGHTS SHOWN ARE TO BE CONNECTED TO EXISTING CIRCUITS IN THE AREA. 1. WIRING FOR CIRCUITS INDICATED TO BE CONNECTED TO THE EMERGENCY SYSTEM SHALL BE KEPT ENTIRELY INDEPENDENT OF OTHER WIRING AND SHALL NOT ENTER THE SAME RACEWAY, BOX, CABINET, ETC. WITH OTHER WIRING. A SEPARATE WIRE AND CONDUIT SYSTEM IS REQUIRED FOR THE EMERGENCY SYSTEM IDENTIFIED AS AN EMERGENCY SYSTEM IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE. 3.RECEPTACLES A.ALL DUPLEX (QUADRAPLEX) RECEPTACLES TO BE MOUNTED 18" ABOVE FINISH FLOOR UNLESS INDICATED OTHERWISE. RECEPTACLES TO BE COMMERCIAL GRADE RATED FOR 20 AMPS 120V. 4.SWITCHES A.LIGHTING SWITCHES SHALL BE RATED FOR 20 AMP 120/277 VOLTS. B.INSTALL WALL SWITCHES 48 INCHES (ON CENTER) ABOVE FLOOR, OFF POSITION DOWN. 5.DATA/ TELEPHONE OUTLET A.ALL DATA/ TELEPHONE OUTLETS TO CONSIST OF FLUSH OUTLET BOX WITH CONCEALED 3/4" METAL CONDUIT RUN TO ABOVE SUSPENDED CEILING. B.TELEPHONE/ DATA WIRING TO BE ACCOMPLISHED BY OWNERS CONTRACTOR. 6.SUPPORT REQUIREMENTS A.LIGHT FIXTURES TO BE SUPPORTED INDEPENDENT OF THE CEILING GRID SYSTEM. THEY SHALL BE SUPPORTED FROM THE BUILDING STRUCTURE WITH JACK CHAINS. B.RESUPPORT ALL EXISTING CONDUIT ABOVE THE WORK AREA. 7.MARKINGS A.MARK EXTERIOR OF ALL JUNCTION BOXES IN THE ELECTRICAL WIRING SYSTEM TO INDICATE CIRCUIT NUMBER AND PANEL DESIGNATION OF ALL CIRCUITS CONTAINED WITHIN IT. 8.FIRESTOPPING A.THE INTEGRITY OF FIRE-RATED WALLS AND FLOORS, WHERE PENETRATIONS ARE MADE FOR THE PASSAGE OF CONDUIT, CABLES, ETC., MUST BE MAINTAINED. 1. ALL PENETRATIONS MUST BE SLEEVED AND FIRE STOPPED WITH MATERIALS THAT ARE UL CLASSIFIED AND FACTORY MUTUAL APPROVED FOR USE IN APPLICABLE RATED ASSEMBLY. 9.PANEL BALANCING A.THE ELECTRICAL CONTRACTOR SHALL BALANCE ALL NEW & EXISTING CIRCUITS AS REQUIRED AT ALL NEW & EXISTING PANELS. 10.DEMOLTION A.REMOVE ALL ELECTRICAL ITEMS IN AREA TO BE RENOVATED. DISPOSE OF ALL ITEMS UNLESS SPECIFICALLY INDICATED TO BE REUSED. 1. EMERGENCY LIGHTS AND EXIT LIGHTS TO BE REUSED. 2. REMOVE ALL CIRCUITS BACK TO PANEL AND REMOVE CIRCUITS FROM PANEL. 3. REMOVE EXISTING DIRECTORY FROM PANEL. PROVIDE NEW DIRECTORY TO REFLECT RENOVATED AREA CIRCUITS. GENERAL NOTES ELECTRICAL NOTES HOME RUN TO EXISTING PANEL - ELECTRICAL CONTRACTOR TO BALANCE PANEL BASED ON NEW LOADS SINGLE POLE SWITCH SECURITY CAMERA PHONE SYSTEM OUTLET FIRE ALARM PULL STATION FIRE ALARM HORN/STROBE FIRE ALARM SMOKE DETECTOR FIRE ALARM HEAT DETECTOR FIRE ALARM DUCT SMOKE DETECTOR FLUSH CEILING MOUNTED SPEAKERS F S F D HF CEILING - MOUNTED EXIT SIGN WALL - MOUNTED EXIT SIGN DUPLEX RECEPTACLE AT 18" OR HEIGHT INDICATED COMPUTER OUTLET DOUBLE DUPLEX RECEPTACLE AT 18" OR HEIGHT INDICATED COMPUTER/PHONE OUTLET UNDERCABINET LIGHTING FIXTURE LIGHT FIXTURE EMERGENCY LIGHT 18" 18" P F F NC NURSE CALL LOCAL ALARM PULL STATION NURSE CALL LOCAL ALARM DOME LIGHT FIRE ALARM STROBE LEGEND OR RECESSED LED LIGHTING FIXTURE PB PUSH BUTTON & DOOR OPENER MANUFACTURERTYPE FIXTURE DESCRIPTION LAMPS A C COLOR TEMPERATURE: 3000K FINISH: MATTE DIFFUSE EXIT LIGHT (SINGLE OR DOUBLE FACE WITH DIRECTIONAL ARROW(S) AS REQUIRED, 120V). PROVIDE SEPARATE CIRCUIT FOR EXIT LIGHTS D ILLUMINATION TO COMPLY WITH APPLICABLE BUILDING CODES B ELECTRICAL FIXTURE SCHEDULE MANUFACTURERTYPE FIXTURE DESCRIPTION LAMPS 1.BIDS SHALL BE BASED ON THE LIGHTING FIXTURE SCHEDULE AND SPECIFICATIONS. REFER TO THE ELECTRICAL SPECIFICATIONS FOR ADDITIONAL INFORMATION INCLUDING SUBSTITUTIONS. 2.ALL FIXTURES SHALL BE UL LISTED. 3.DRIVERS SHALL BE UL LISTED AND SHALL BE THE MANUFACTURER'S SPECIFIED DRIVER FOR THE FIXTURE OR SHALL BE VERIFIED COMPATIBLE BY BOTH THE DRIVER AND FIXTURE MANUFACTURERS. 4.ALL FIXTURES SHALL BE COMMERCIAL GRADE WITH AN EXTENDED SERVICE LIFE TIME. 5.ALL NECESSARY MOUNTING HARDWARE, HANGERS,BRACKETS, RAILS, YOKES, STEMS, CHAINS, ETC., SHALL BE FURNISHED AND INSTALLED. 6.REFER TO ARCHITECTURAL DRAWINGS FOR SPECIFIC DETAILS, ARRANGEMENT, MOUNTING HEIGHTS, CEILING CONSTRUCTIONS, ETC. ALL COLORS AND FINISHES SHALL BE VERIFIED BY THE ARCHITECT. 7.FIXTURES SHALL BE SEISMICALLY SUPPORTED AS REQUIRED BY THE APPLICABLE BUILDING CODE. 8.WIRE ALL BATTERY PACK UNITS (I.E. EXIT SIGNS AND EMERGENCY UNITS) TO LINE SIDE OF LOCAL LIGHTING BRANCH CIRCUIT. 9.ALL FIXTURES RELOCATED TO BE RELOCATED SHALL BE CLEANED AND SERVICED PRIOR TO RE-INSTALLATION. LIGHTING FIXTURE NOTES E EXISTING TO REMAIN RL RELOCATED EXISTING DEVICE/ FIXTURE NL LOCATION OF RELOCATED DEVICE/ FIXTURE X X X X X X LITHONIA LIGHTING MODEL #: 2ALL2 CTRF 33L SLD LP830 RECESSED 2'x2', CENTER FILL L.E.D. LIGHT LUMENS: 3300 VOLTAGE: MVOLT (120-277V) DRIVER: STEP-LEVEL DIMMING COLOR TEMPERATURE: 3000K RECESSED 6" ROUND L.E.D. DOWNLIGHT LUMENS: 2000 VOLTAGE: MULTI-VOLT DRIVER: ELDO LED 10% 0-10V DIMMING LITHONIA LIGHTING MODEL #: LDN6 30/20 L06 AR LD MVOLT EZ10 LITHONIA LIGHTING MODEL #: 2ALL4 CTRF 48L SLD LP830 RECESSED 2'x4', CENTER FILL L.E.D. LIGHT LUMENS: 4800 VOLTAGE: MVOLT (120-277V) DRIVER: STEP-LEVEL DIMMING COLOR TEMPERATURE: 3000K MATCH BUILDING STANDARD 1.ALL FIXTURES SPECIFIED ON AN "OR EQUAL" BASIS AND SUBJECT TO APPROVAL BY OWNER LIGHT FIXTURE NOTE ELECTRICAL LIGHTING PLAN SCALE: 1/8" = 1'-0" UP TOILET CLOS 005 OPEN OFFICE 001 OFFICE 002 OFFICE 003 OFFICE 004 OFFICE 006 CORRIDOR 007 F F F P F DN RECEPTION 103 OFFICE SPACE/CUBICLES 105 OFFICE 111 I.T. 109 CONFERENCE 104 ENTRY VESTIBULE 102 UP D.F. TOILET SUPERVISOROFFICE 107OFFICE 112 OFFICE 106 LOBBY 101 OFFICE SPACE/ CUBICLES 108 AISLE 110 REFLECTED CEILING PLAN SCALE: 1/4" = 1'-0" PROJECT AREA B B B B B B B B BBB B B B B B A A A A A A A A A A B B B B B B BBB B B B BB B B B B B B C C C C C CCCCC C C C D D D UP TOILET CLOSE 005 OPEN OFFICE 001 OFFICE 002 OFFICE 003 OFFICE 004 OFFICE 006 CORRIDOR 007RAD.DN RECEPTION 103 OFFICE SPACE/CUBICLES 105 OFFICE 111 I.T. 109 CONFERENCE 104 ENTRY VESTIBULE 102 UP D.F. TOILET SUPERVISOROFFICE 107 RADIATOR RAD. OFFICE 112 OFFICE 106 LOBBY 101 OFFICE SPACE/ CUBICLES 108 AISLE 110 PROJECT AREA ELECTRICAL POWER PLAN SCALE: 1/8" = 1'-0" NOTE: EXISTING ELECTRICAL SWITCH LOCATIONS TO REMAIN. PROVIDE NEW DIMMING SWITCHES AT EXISTING LOCATIONS SERVED BY EXISTING CIRCUITS. DEDICATED NOTE: COORDINATE WITH FURNITURE VENDOR REGARDING REQUIRED POWER AND DATA WHIP LOCATIONS 12/20/2017 4:59 PMELECTRICAL LIGHTING AND POWER PLAN E101 RK SEAL: MARK DATE ISSUE --- PROJECT NO: PROJECT ARCHITECT: PROJECT MANAGER: DRAWN BY: DATE: COPYRIGHT: 17-055 REK REK 12/20/2017 SHEET TITLE: CONSULTANT: 64 GOTHIC STREET, SUITE 1 NORTHAMPTON, MA 01060 T 413.585.1512 F 413.586.7945 www.haiarchitecture.com H AI Architecture, Inc. Loan Servicing Department 1st Floor Florence Bank 85 Main Street Florence, MA 01062 Renovation for: PROJECT: